外国网站看到的，布包包教程（转贴）

爱上DIY · 发表于 2012-5-26 18:36:33

学布艺就上布流行，最大的布艺手工论坛邀您注册！

您需要登录才可以下载或查看，没有帐号？注册会员

x

看上去，外国人做包包比较简易，不铺棉，不滚边，哒哒哒哒哒哒哒哒，就好了。

这个教程是原作者把一个标准的buttercup bag纸样经过自己调整尺寸，另外安装拉链，内袋改为立体什么的。偶简单翻译一下。

A couple of words of advice.  If you choose to interface the lining, the outer top and the handle and you sandwich the strap between the lining and outer - make sure your machine can handle thick layers otherwise you'll be breaking lots of needles!!!

给袋子加条拉链的方法：调整原来的纸样，把里布的纸样裁成两个部件，从顶部向下裁1英寸，每部分折出四分之一英寸的边。

OK.  Firstly, I'll show you how I added the zipper.  You need to start by altering your pattern.  Cut the lining an inch or so down from the top, then add 1/4" seam to either piece, like this:
2009-5-20 10:34 上传
下载附件 (18.88 KB)

需要裁另外的4个布条，分别缝在拉链的两边和两端
Then cut your pieces for the bag.  You need to cut extra pieces.  4 pieces, width of the zipper x probably 2 or more inches (for the ends of the zipper) and another 4 pieces, 2 inches x a bit longer than the length of the outer upper piece of the pattern (for the sides of the zipper).  If this is a little confusing now, it may make more sense in the pictures further down.  You need to add the little tab bits to the ends of the zipper like this:

Then you need to add the side bits to the zipper, like this:

拉链居中Then you need to cut the whole piece to 1 3/4" wide x length of outer upper piece, centering the zipper, like this:

把拉链夹在里布的顶和底部这两片部件之间：Now you need to sandwich the zipper between the lining bottom and top, like so:

另一侧同样操作Repeat for the other side. This is what it should look like:

缝合里布：Then sew the lining together. With the ends of the zipper, make sure they go 'upwards' when catching in the lining, like this:

留出一个开口好翻面过来Make sure you leave an opening in the lining to turn right sides out:

OK. This ends the tutorial on the zipper.

如何做一个立体的手机袋（可能原来的纸样是个平面的内袋）Now onto how I did the mobile phone pocket. I cut two squares of fabric (outer and lining) 5 x 5 inch square with 1" squares cut from the bottom of each fabric, like this:

正面相对缝合顶部Put right sides together and sew across the top:

Sew the corners of lining and outer:

Put right sides together. Sew around edge leaving gap for turning:

Turn right sides out. Press and top stitch along top edge:

固定在里布上Pin to lining:

缝合在里布上Sew to lining:

褶皱的做法Finally, the pleats. I followed the directions of the pleats but somehow, I could not get them to fit. This is how I ended up doing them. I must say, that I do like this way:

I placed a pin in the middle of the fabric. I pinned the other 4 pleats according to the pattern. This is what it looked like:

Start by sewing the pleated edges with the outer top piece on the top towards the centre but stopping before the centre, like this:

Start and the other end and stop before the centre. Create a box pleat and continue to meet the other line of stitching:

成品You should end up with something that looks like this:

Hope this is helpful. As always, if you have any questions, fire away!!!